秋霞黄色网 I 免费av一级片 I 久久国产网站 I 动漫美女被人操 I 高清黄色大片 I 免费不卡的av I 欧美极品少妇xxxxⅹ免费视频 I 日本黄大片在线观看 I 巨乳中文字幕在线观看 I 在线免费av观看 I 亚洲黄色片在线观看 I 黄色片视频在线观看 I 让领导弄进去了的娇妻 I av人体 I 欧美 日韩 国产 激情 I 美女调教vk I 日韩第一视频 I 在线不卡的av I 日本视频网站在线观看 I 精品在线视频一区二区三区 I 美女狂揉下部 I 亚洲日本va中文字幕久久 I 网红主播av I 酒店大战丝袜高跟鞋人妻 I 国内精品 中文字幕 I 久播影院在线观看 I 青娱乐超碰在线91 I www.成人深夜激情 I 亚洲精品电影久久久 I 婷婷久久综合九色综合88 I 国产精品亚洲а∨天堂123bt I 尤物视频在线观看网站 I 亚洲成aⅴ人最新无码 I 日韩三级黄色毛片 I 久久人搡人人玩人妻精品 I heyzo少妇av精东影视 I 丰满五十六十老熟女hd I 曰本色欧美视频在线 I 亚洲交换

 

 

 

The application of atomic ash on sheet metal needs to be carried out in sequence: grinding off old coating film and rust, making feathered edges, cleaning and degreasing, spraying primer, stirring atomic ash, applying atomic ash, drying, and grinding atomic ash surface.

 

 

 

Tool for removing old coating and rust: single action grinder, 60 grit sandpaper

 

 

 

Make a feather shape

 

 

 

The purpose of this step is to prevent obvious linear traces of atomic ash after polishing. Making feathered edges can cause foggy atomic ash marks to appear on the polished surface, facilitating the next spraying operation and avoiding obvious pits after application.

 

 

 

Tool: Double action grinder, 120 grit sandpaper,

 

 

 

When grinding, pay attention to raising one side of the grinder by about 10mm and moving it gently along the edge

 

 

 

Cleaning and degreasing

 

 

 

Spraying primer can be done using a brush or spray gun.

 

 

 

Stir atomic ash

 

 

 

Mix the atomic ash and hardener evenly, take out the required amount of atomic ash and the correct proportion of hardener, and finally use a scraper to stir the atomic ash and hardener at the corners.

 

 

 

The method of stirring atomic ash and hardener at the edges and corners of the scraper When applying atomic ash, the standing position must be able to easily apply to the farthest damage area without excessive stretching of the arm. Fill small depressions with a thin coating to avoid porosity and enhance adhesion;

 

 

 

Adding atomic ash causes the atomic ash surface to be higher than the old coating film without generating bubbles. The next time atomic gray is applied, the application range should cover at least one-third of the previous application range.

 

 

 

Finally, move the scraper in the opposite direction to scrape the edge of atomic gray and level it.

 

 

 

Dry at room temperature as required, or use Far infrared drying lamp to force drying. To grind the atomic ash surface, the first step is to determine whether the atomic ash has dried, that is, to check whether the ground atomic ash is easy to brush off. Note: If the thin area of atomic ash application has dried, it indicates that the entire atomic ash application area has completely dried. There are also two ways to grind according to needs, one is to use a circular track grinder for grinding, and the other is to use a hand grinding pad for grinding. Circular track grinder grinding tool: Circular track grinder, approximately 80 grit sandpaper

 

 

 

Hand grinding pad grinding tool: Grind the pad with approximately 120 grit sandpaper to a certain extent, and use an air gun to blow off the ground powder to check for pinholes on the atomic ash surface. Finally, replace the sandpaper with 240 sandpaper and polish the sandpaper marks.